TD-4100 XDC











Specifications

Applications Steam Condensate, Boiler Feed, Normally Clean Water
Hydrocarbons Fuel Oil, Crude Oil, Other Fuels and Oils, Phenol, Styrene,Most Heat Transfer Fluids, Aromatic Chemicals, BTEX
Detection Range: Fuel Oil, Crude Oil 5 ppb in Steam Condensate - 500ppm
Low Detection Limit: Other Hydrocarbons Depends on the Type, Generally < 50ppb
Dimensions 20" x 16" x 11" (50.8cm x 40.6cm x 27.9cm)
Weight 65 pounds (29.5kg)
Local Display Yes, PPM, PPB, Or Raw Signal
Controls External 316 SS Touch Pad
Power Requirements 90 - 240 VAC, 2A, (24 vdc Optional)
Plumbing Requirements Feed: 3/8" or 1/2" Tube, Return: 3/8"or 1/2" Tube
Sample Pressure <150psig, 10barg (For higher pressures consult factory)
Sample Temperature 100°C, 212°F (For higher temperatures consult factory)
Required Air Supply General Purpose None
Required Air Supply Zone I, Zone II 15 scfh
Ambient Operating Temperature 32°F - 121°F, 0°C - 49°C (Heater or Vortex Cooler Optional)
Flow Cell Characteristic Closed Tube with Internal Cell Condition Sensor
Pressurized Sample Return Yes
Operational Principle UV Fluorescence
Calibration Stability +/- 10% over 6 Months
Response Time 3 seconds full scale spike change, continuous reading
Calibration Blank / Standard Addition or Correlation to Standard Methods
Reagents None
Alarms 4: Early Warning / High Alarm / Cell Condition / CIP
Alarm Contacts Dry Contact AC/DC
Outputs 4-20 mA,24 vdc powered, 500 ohm impedence
Communication Protocols Optional: Hart, Mod Bus
Diagnostics Self Diagnostics, internal failure linked to alarm, Cell Condition
Security Password Protects Software, Lockable Enclosure
Electronics Cabinet 316 SS
IP Rating IP W 66, NEMA 4X
Maintenance Calibration Check, Clean Flow Cell
Cleaning Chemicals Detergents and/or Dilute HCL
Explosion Proof Options Gen Purpose, (Optional C1D2, Atex Zone II, C1D1, Atex Zone 1)

Sample Pump

 Optional
Semi Automatic Cleaning System Optional
Data Logger Optional

 

©2007 Turner Designs Hydrocarbon Instruments
2023 North Gateway, Suite 101
Fresno, CA 93727

(559) 253-1414
(559) 253-1090 - Fax

Gulf Coast Office
2200 N. Loop West #126
Houston, TX 77018

(713) 263-9099
(713) 263-9228 - Fax

Technical Data Sheet

TD-4100 XD C Oil in Water Monitor

United States Coast Guard (USCG) Certifies the TD-4100 and TD-4100 XD for 15 ppm Bilge Alarm Monitoring

July 1999 - The USCG certified both the Turner Designs TD-4100 and TD-4100 XD on-line oil in water monitors as Oil Content Meter – 15 ppm bilge alarms. The USCG certifies that the oil content meters comply with the 15 ppm bilge alarm regulations stipulated by regulation 16(5) of Annex I to Marpol 73/78. This certification package comes on the heels of the Canadian Coast Guard Certification of the TD-4100 as a 5 ppm bilge alarm that was issued in January 1999. The USCG certification lead to an immediate American Bureau of Standards (ABS) approval letter for the TD-4100 XD deployment on an ABS classed vessel.

"The TD-4100 series non-fouling detection technology finally solves the marine industry’s expressed concern that traditional oil in water monitoring technology is simply unreliable" said Mark Uhrich, Director of Sales and Marketing. "The TD-4100 series oil in water monitors repeatedly demonstrate low maintenance performance enjoyed by the oil & gas industry for offshore platforms, FPSO’s, FSO’s and drilling rigs. Now with USCG certification the marine industry can significantly improve their bilge water discharge programs."